ShllShockArcade

Forum Replies Created

Viewing 7 posts - 1 through 7 (of 7 total)
  • Author
    Posts
  • November 3, 2022 at 9:34 PM in reply to: DExx video output issues with Arcade PCB #55627
    ShllShockArcade
    Participant

      Hey Marqs,

      I also own your OSSC and that is correct I get no sync with that either with my TMNT – OSSC just shows no Sync I believe. I May be the one that has recently been reporting this issue as a matter of fact. Reason I bought the DExx was hoping that this would resolve the issue when using Scaler mode as apposed to line multiplier but still no luck.

      What do I look for on the DExx for OSD indication? Are there flashing lights on the board to look at since it doesn’t have a display like the OSSC?

      I am going to ask friends and family to chip in for an o-scope for my Xmas present this year so I might be the one looking into this myself 🤣 might need assistance as to where I should probe the sync signal though as I’m still learning all of this.

      Thanks again Marqs,
      Adam

      November 3, 2022 at 7:31 PM in reply to: DExx video output issues with Arcade PCB #55624
      ShllShockArcade
      Participant

        Thanks again Marqs for the advice. Tried reducing Analogue Sync Vth to 0mv with no success.

        What could cause this board in particular to not sync properly? Any ideas what could be different internally to all of my other JAMMA edge boards?

        November 3, 2022 at 11:59 AM in reply to: DExx video output issues with Arcade PCB #55619
        ShllShockArcade
        Participant

          Hi Marqs,

          If I switch video output back to OSD I can get back into the OSD without a problem. Yes I’ve attempted turning off frame lock and ram through all of the frequency options.

          Question – when I adjust these options do I have to save and reboot for them to take effect or should it be instantaneous?

          November 2, 2022 at 12:07 PM in reply to: DExx-vd_isl fw 0.61 #55604
          ShllShockArcade
          Participant

            I get a black screen. Audio of the game still playing in the background. I’ll open a new thread, thanks Bucko 👍🏼

            November 2, 2022 at 6:12 AM in reply to: DExx-vd_isl fw 0.61 #55601
            ShllShockArcade
            Participant

              Running latest firmware and don’t seem to be getting an image while in either scaler mode or line multiplier mode for TMNT arcade PCB.

              Running through HAS SuperGun 8-pin mini din to RGB input on the Dexx, hdmi out to my lcd tv. All other PCB’s work in scaler and line multiplier. What could cause this?

              Note: TMNT PCB works fine in my arcade cabinet w/ wells Gardner k7000 series 15khz crt

              November 1, 2022 at 11:30 PM in reply to: Issue with DExx-vd_isl (DE10-nano) in scaler mode #55598
              ShllShockArcade
              Participant

                Yup, this completely cleaned up the jitter 👍🏼 One thing that might need to be addressed. Bob from Retro RGB just posted a new orientation for the dexx based on the new firmware update. He should possibly be notified if you are saying that this hack should not be used in conjunction with swapping the MiSTer on and off of the de-10 nano … might damage people’s boards maybe?

                November 1, 2022 at 10:58 PM in reply to: Issue with DExx-vd_isl (DE10-nano) in scaler mode #55596
                ShllShockArcade
                Participant

                  Hi guys, having the exact same issue in scaler mode = bad jitter in 1080p going to attempt solder hack and will report back

                • Author
                  Posts
                Viewing 7 posts - 1 through 7 (of 7 total)