[the_lilleorg]

Anyome else have a OSSC and uniracers ?

Im using a SCART cable , RGB

[the_lilleorg]

is that even a thing, or enough to trick a TV to thinking the freq is doubled?

[the_lilleorg]

Would love to see profiles with set inputs ,where the profile could support AV1 or AV2 etc.

also awesome if it could have a breakout pin. Im looking at integrating a switcher unit with this and having a axtra pin to sync with the profile would be awesome. ex profile 4 is 4 pulses

[the_lilleorg]

I have enabled passthru or “direct” as the output mode.

its having issues with the 15.73Khz signal (FW 0.73)

Using the 480i passthru in the menu causes a “resolution error”

Is there a way to bump this to 31.73 khz (or super impose this)

I have tried a Xbox 480P games (Burnout revenge) and a 480i games (Starwars/tetris) that worked fine in i /p

The PS2 as thru component is not working in the slightest (Ps2 Slim)

[the_lilleorg]

Now that I have a programmed remote I can finally See all the settings. but for the life of me I cant getthe Yprbr input (xbox ) to display. if I set the output to 575i passthru I get a resolution error on the AV receiver and the TV shows “not available ” instead of no signal.

the other picture modes “3x or 2x ” don’t seem to change that number.

I also think that the Tripling / doubling is not takng affect on the test pattern screen.

UPDATE:

Using my TV (Olevia 747i ) it was telling me the displayed resolution when line doubler was on was 1360×1024 . its a weird resolution that wouldn’ t allow the receiver to work (blue screen signal)

not sure how to enable the tripler, switching it to on didnt do anything .
currently i have it running as 480P with scanlines ^% and then running to the onkyo with output set to 1080p . looks very stunning for the xbox . the rest of the settings are defaults. (Xbox confirmed works )

I’m still learning about this device but I found that resolution odd

UPDATE:

It looks like Games work but the main menu does not:

When Game is inserted: 31.46Khz , 525P 59.94Hz
When menu/startup : 15.73Khz , 525i , 59.94Hz

Whats the cause for this Frequency change and how can we have the OSSC detect this?

[the_lilleorg]

Now that I have a programmed remote I can finally See all the settings. but for the life of me I cant getthe Yprbr input (xbox ) to display. if I set the output to 575i passthru I get a resolution error on the AV receiver and the TV shows “not available ” instead of no signal.

the other picture modes “3x or 2x ” don’t seem to change that number.

I also think that the Tripling / doubling is not takng affect on the test pattern screen.

Is there any way to not have it out as 525i

[the_lilleorg]

the Toshiba codes work rather well with the device. awesome work.

[the_lilleorg]

The TX-NR515 does support up scaling to even 4K.

from my understanding the OSSC isnt a frame buffer so there could be a few less or more lines that could be affecting the picture.

http://www.intl.onkyo.com/products/av_components/av_receivers/tx-nr515/index.html

[the_lilleorg]

Just to update you all:

Without selecting AV1-3 I can see the test pattern.

Running the “display” command I see that the test pattern is HDMI IN RGB 24Bit 720×480.

The Input source on the Xbox is set to AV2 (Component cables )

the ossc shows 525i , 15. 73Khz 59.94hz

I assume i need 480P / I out not the 525 PAL ?

[Author]

Posts