Ricardo Santos

Forum Replies Created

Viewing 10 posts - 1 through 10 (of 10 total)
  • Author
    Posts
  • October 8, 2020 at 4:23 AM in reply to: Sega Genesis (Model 1) Sync on OSSC but Black Screen Output. #41936
    Ricardo Santos
    Participant

      Were you using scart cables? I’m having the same issue

      September 30, 2020 at 5:55 AM in reply to: Compatible SD cards #41676
      Ricardo Santos
      Participant

        I’m trying a microSD HC card and it says, card not detected. Already formatted the card on fat32, also wrote the image using Win32disk imager. No luck, I guess I need to try a different SDcard.

        Can anybody confirm if microSD HC cards work?

        September 30, 2020 at 4:59 AM in reply to: OSSC several issues #41673
        Ricardo Santos
        Participant

          Hi marqs, thanks for the tip. I looked at the components around the BTN1 and turns out I had soldered SD05-7 at D4 on the wrong polarity. After I fixed that the OSSC started to power up properly without prompting the RC setup. BTN1 still doesn’t seem to do anything when I press it but BTN2 started working. However, I don’t care about the buttons now that the remote works properly.

          The only thing left to fix is the SDcard port, it keeps saying there’s no sdcard on the slot, I already tried 2 different cards and nothing changes. I don’t really know how to test continuity for this. Maybe I messed up the component? I can order another one to see if that’s the case.

          September 28, 2020 at 10:43 PM in reply to: OSSC several issues #41611
          Ricardo Santos
          Participant

            I saved a profile but it’s still asking me to setup the remote every time I turn it on.

            September 26, 2020 at 5:24 AM in reply to: OSSC several issues #41545
            Ricardo Santos
            Participant

              marqs, where are the remote settings saved? is it on sdcard? if yes, then I’m in trouble, like I said, the SDport is not recognizing any cards

              September 25, 2020 at 6:45 PM in reply to: OSSC several issues #41526
              Ricardo Santos
              Participant

                Hi marqs, thanks for helping out, really appreciated.

                – When you say “save settings” you mean saving profile settings? Or there’s another way to save settings?

                – How do I verify connectivity between the SDcard port and the FPGA?

                September 24, 2020 at 12:16 AM in reply to: [Parts] Problem sourcing a few of them #41490
                Ricardo Santos
                Participant

                  You can safely replace the IRM-V5XX_TR1 with a TSOP31338. I tried it and it works well. The pinout is different, so, make sure to read the datasheet.

                  Thanks to a suggestion from marqs

                  September 23, 2020 at 5:59 AM in reply to: Replacing IRM-V5XX_TR1 #41481
                  Ricardo Santos
                  Participant

                    I figured it out. It was just the remote wizard. I found an old remote I had and went through the wizard. Now it shows:

                    OSSC fw. 0.81a
                    2014 – 2018 marqs

                    marqs what’s the latest firmware version and where do I check for firmware updates?

                    Regards

                    September 23, 2020 at 5:22 AM in reply to: Replacing IRM-V5XX_TR1 #41480
                    Ricardo Santos
                    Participant

                      I soldered the TSOP31338 powered the OSSC, the green LED light up and the LCD display now says “Press 1” I pressed button 1 but nothing happens.

                      I think that’s not the expected behavior, I saw some videos and what should show up is “OSSC 1.6 …”
                      Does that mean my OSSC is not programmed?

                      September 18, 2020 at 8:32 PM in reply to: Replacing IRM-V5XX_TR1 #41398
                      Ricardo Santos
                      Participant

                        Hi marqs, do you think this TSOP31338 would work on the OSSC? I mean is it just a matter of soldering it to the board? or I’d have to reprogram something?

                      • Author
                        Posts
                      Viewing 10 posts - 1 through 10 (of 10 total)