sofakng

Forum Replies Created

Viewing 13 posts - 1 through 13 (of 13 total)
  • Author
    Posts
  • October 20, 2023 at 3:56 PM in reply to: OSSC v1.xx series beta firmware #58362
    sofakng
    Participant

      Is this new firmware able to support VGA (720×400, etc) to 1440p @ 70 Hz using pixel repetition?

      September 24, 2023 at 2:58 PM in reply to: Can the OSSC or DExx simulate a shadow mask oraperture grille? (re: VGA monitor) #58115
      sofakng
      Participant

        That’s fantastic!!  Thanks so much!

        September 4, 2023 at 3:56 PM in reply to: OSSC v1.xx series beta firmware #57937
        sofakng
        Participant

          Any possibility of 480×3 resolution?  (ie. DOS VGA -> 1440p)

          June 30, 2023 at 9:40 PM in reply to: Can the OSSC or DExx simulate a shadow mask oraperture grille? (re: VGA monitor) #57340
          sofakng
          Participant

            Thanks for the reply and the information.  Maybe there will be enough users so that you could consider implementing it.

            Regardless — I have one other quick question…

            I’m trying to use 1200p output (which I know is out-of-spec/unsupported) from my VGA monitor to my LCD.

            The OSSC has two options in “384/400p proc”: Line3x Generic and Line3x 240×360.  However, if I select either mode then the ‘400p in sampler’ options do not work.  Is this intended? If I use Line2x then both sampler options work correctly.

            My goal is to try and display VGA 640X400 and 720×400 at 1200p.

            Thanks for any help!

            June 16, 2023 at 3:02 PM in reply to: Can I use the 20×2 LCD with the DExx? Also, any 3D printable cases? #57236
            sofakng
            Participant

              Thanks again for the information. It sounds like you are saying the 20×2 is the better LCD but might not fit correctly with the DE10-Nano attached.

              Also, it looks like New Haven discontinued the white color in both the 16×2 and 20×2 versions which is unfortunate.

               

              June 15, 2023 at 5:03 PM in reply to: OSSC v1.xx series beta firmware #57225
              sofakng
              Participant

                Thanks very much.  I’ve performed the modification and updated successfully.  I’ll run a few tests in the next few days.

                June 15, 2023 at 3:27 AM in reply to: OSSC v1.xx series beta firmware #57213
                sofakng
                Participant

                  Does this firmware improve compatibility with DOS PCs?

                  I also have a DExx board but I usually don’t have it connected to the DE10-Nano because I’m using MiSTer with dual SDRAM.  However, I’ve been searching for the best way to convert VGA/SVGA (DOS) to my 1440p monitor (at 70 Hz).

                  If anybody has any other advice, info, or experiences with this please let me know!

                  June 13, 2023 at 1:41 PM in reply to: Can I use the 20×2 LCD with the DExx? Also, any 3D printable cases? #57212
                  sofakng
                  Participant

                    Thanks for the reply.  Are you sure it won’t use the extra space?  Hopefully Marqs can confirm since he mentioned the 16×2 only being used because the 20×2 wasn’t available at the time and that the 16×2 does cut-off some characters due to it being too small.

                    August 6, 2020 at 10:04 PM in reply to: What are Optimal GameCube GBIHF settings when using RGB SCART? #40392
                    sofakng
                    Participant

                      Thanks!

                      Is it possible to have the GBP output its native rate? It sounds like HDcustom is close but still not the same rate?

                      August 6, 2020 at 8:58 PM in reply to: What are Optimal GameCube GBIHF settings when using RGB SCART? #40390
                      sofakng
                      Participant

                        What is the difference between “HD60” and “HDCustom” ? I’m trying to read the documentation but the –format options is only described as “Set video format”.

                        June 5, 2019 at 9:22 PM in reply to: USB port for serial console access #26522
                        sofakng
                        Participant

                          @marqs, any update on this?

                          Being to send commands (and receive status updates) over UART would be incredibly useful. You could then see the current OSSC status without needing to see the small LCD screen. It would also be extremely helpful in home automation setups.

                          July 24, 2018 at 12:13 AM in reply to: Tips & Tweaks: Lx3, Lx4, Lx5 modes #22554
                          sofakng
                          Participant

                            Yeah I did try all the way down to one and it didn’t work. Anything else I can try?

                            July 23, 2018 at 4:13 PM in reply to: Tips & Tweaks: Lx3, Lx4, Lx5 modes #22548
                            sofakng
                            Participant

                              I’m trying to get my Panasonic TCP50GT25 plasma working with NES/SNES Line3x-5x but I’m not having any luck.

                              When I enable Line3x, I’ve tried going into Advanced Timings (960x240p) and setting V. Active Lines to 256 and V. Backporch to 6 but it didn’t help.

                              Is anything else I can try before thinking about the recent sync mod that marqs released?

                            • Author
                              Posts
                            Viewing 13 posts - 1 through 13 (of 13 total)